Manuals
Contents
Previous
Next
| | | |
| |||
| |||
| | | |
| ManualsContentsPreviousNext | | |
This section describes the paper size, feed direction, and the maximum amount of paper that can be loaded into each paper tray in this printer.
All paper must be set vertically, regardless of the paper size.
In this manual |
On the display |
Paper feed direction |
|---|---|---|
|
A4 8 1/2 × 11 |
Short-edge feed direction |
Input Paper Sizes (Metric version)
Size (mm) |
Size (inch) |
Standard Input Tray 1 |
Paper Feed Unit TK1010 (Tray 2) |
Bypass Tray |
Duplex |
|
|---|---|---|---|---|---|---|
A4 |
210 × 297 |
8.26 " × 11.69 " |
|
|
|
|
B5 |
182 × 257 |
7.17 " × 10.12 " |
|
|
|
|
A5 |
148 × 210 |
5.83 " × 8.26 " |
|
|
|
|
A6 |
105 × 148 |
4.13 " × 5.63 " |
|
|
|
|
Legal |
216 × 356 |
8.5 " × 14 " |
|
|
|
|
Letter |
216 × 279 |
8.5 " × 11 " |
|
|
|
|
Executive |
184 × 276 |
7.25 " × 10.5 " |
|
|
|
|
F/GL |
203 × 330 |
8 " × 13 " |
|
|
|
|
Foolscap |
216 × 330 |
8.5 " × 13 " |
|
|
|
|
Folio |
210 × 330 |
8.25 " × 13 " |
|
|
|
|
Com10 Env |
104.8 × 241.3 |
4.25" × 9.5" |
|
|
|
|
C5 Env |
162 × 229 |
6.38" × 9.02" |
|
|
|
|
C6 Env |
114 × 162 |
4.49" × 6.38" |
|
|
|
|
DL Env |
110 × 220 |
4.33" × 8.66" |
|
|
|
|
Monarch Env |
98.4 × 190.5 |
3.875" × 7.5" |
|
|
|
|
16K |
195 × 267 |
7.68 " × 10.5 " |
|
|
|
|
Custom Paper Size |
- |
- |
|
|
|
|
Use the control panel to specify the size.
Use the control panel to specify a size as a custom size.
The following sizes are supported:
Tray 1 (approximately): width 90 - 216 mm (3.54 - 8.5 inch); length 148 - 356 mm (5.83 - 14 inch)
Bypass Tray (approximately): width 90 - 216 mm (3.54 - 8.5 inch); length 148 - 356 mm (5.83 - 14 inch)
The size is not supported.
Paper weight and number of sheets to be set
Supported paper weight |
Maximum number of sheets (plain paper) |
|
|---|---|---|
Tray 1 |
60 - 160 g/m2 (16 - 42 lb.) |
250 (80 g/m2, 20 lb.) |
Bypass Tray |
60 - 160 g/m2 (16 - 42 lb.) |
1 |
Paper Feed Unit (Tray 2) |
60 - 105 g/m2 (16 - 28 lb.) |
500 (80 g/m2, 20 lb.) |
Check that the top of the stack is not higher than the limit mark inside the tray.
 |
 | Copyright (C) 2008 |
(Feed direction)